Solid waste incinerator, productivity 100kg/h placed in a container. Dimensions: 2,45×12,2m and 2,9m in height. Operates natural gas with the pressure of 0.005 MPa and consumption of 0,21-0,23 m3 per kg of waste. Installed power C 55 kW. Total 3 units. Fuel capacity:200l or more Incinerator has a temperature monitoring system in place Wet scrubber capable of removing sulpur dioxide in the fumes Water capacity of 2000l or more Incinerator temeprature above 950 degree celsius Incinerator used a dual chamber system for incinerator Capacity per hour at least 25kg 1. A combustion chamber : a. watertight door for manual loading of waste. b . A burner start is limited to inflammation of waste . 2. A camera post-combustion gases : a. burner combustion , low power . b . An injection device air for total recombustion of the gases . c . An input device cooling air of the combustion gases. d . A smoke evacuation duct . 3. A control panel ensuring complete combustion cycle . The incinerator meets as indicated on waste incineration . They will not burn plastics, packaging except that the amount so small that gases need not receive any treatment, secondary combustion chamber to 1100C handles everything .. Water waste incinerator, productivity up to 3m3/h and placed in a modular building. Dimensions: 8,2×5,9m and 5m in height. Operates natural gas with the pressure of 0,016 MPa and consumption of 0,35m3 / kg of drainage. Installed power C 35 kW. Total 1 unit.
the incinerator is required to burn the eggs and where the eggs contain a quantity of fluid and embryos, the purpose of the burner is to use whole eggs for the right highly dangerous viruses,in addition.gas emission will be discussed according to the requirements of the egyptian ministry of environment. in the event of approval, a pilot test (fat test :factory acceptance test) will be carried out at the company’s site on 2000 to 3000 eggs. also we will burn this waste in the incinerator such dead chicken and also some plastic materials. please give replay if this model of incinerator can get rid of this waste or not the list of waste 1- Eggs contain amount of fluid and also embryos. 2- dead chicken and also some plastic materials. 1. Dual Chambered( first chamber attainable temperature(800-900 Celsius) (2nd Chamber 1200-1300 degree Celsius) 2. WITH WET SCRUBBER ( very important- this basically neutralizes the gases with Alkaline water ) 3. Minimum required capacity is 500 Kg/HR 4. MEETING PAKISTAN EPA STANDARDS AS PER ATTACHED LIST 5. After the water is treated in the scrubber and let down to the drain and what is the limit of the heavy particles present in it and how can it be treated? 6. How much diesel does it burn in an hour during burning / operations? 7. What is the total consumption of electricity. How many KILOWATTS does it require to operate.? 8. We like to know if you can provide us the FLUE GASES ANALYZER in the control panel (It Measures the gases during the process) of incineration? 9. We will be needing ITALIAN burner and SIEMENS control panel. 11. After sale service details and warranty ? 12. Spare parts that you provide with the unit. 13. Pakistan EPA standards we gave you during the meeting the unit should meet these. 14. Quotation with the FLUE GASES ANALYZER and without the FLUE GASES ANALYZER . 15. Physical Test is must before the Deliver
I require an incinerator which is capable of burning between 3 to 5 tonnes per day of mixed waste products, plastics, rubber, flammable putrescible waste, medical waste, rubber tyres, paper and cardboard, textiles, green timber waste etc. As some of the waste products will contain non-flammable solids, the incinerator should be capable of extracting those materials probably via a rotary kiln process. It is not intended to use any fuel, such as oil or diesel, to promote the burning of the waste, as the waste products are required to be incinerated using a free burning process. Hot air however from a downstream process will be available to increase the incinerator temperature and burning rate as required. Very high temperatures in the incinerator are not necessary and are not required. The afterburner is strong sheet steel flange connection. Internal filling refractory concrete with very high alumina content ( 65 % H2 03) and a thickness of 150 mm . thermal insulation panels made ??of fibrous silicates and calcium with a thickness of 85 mm . diesel or gas burner (must be specified in the order ) , monobloc horizontal flame , electronic ignition , safe , permanent ventilation , control valve and isolation valve. air injection nozzles made ??of refractory steel with a flow control valve. These nozzles are specially designed and patented by ATI to guarantee very low hydrocarbon emissions. A secondary air injection is scheduled and ensures perfect oxygen content. Fan distribution primary and secondary air , the air flow regulation is effected by means of valves and actuators on automatic cycle commands. The burning of the waste products is expected to produce toxic emissions which will be cleaned via other existing downstream processes and a Post Combustion process in the incinerator is therefore not required. we are seriously searching a chicken waste destroyer for slaughter shop, we have more than 250 shops in our locality, if those machine click as useable for each and every shops, we are sure we can sell the machine like hot cakes . Recently our municipality issued a circular for self destroying scheme for chicken waste at each shop itself our requirements It should be portable unit chicken waste: feather, skin, legs, head and other chicken related waste parts capacity: each shop slaughter nearly 100 to 250 chicken waste per day incineration: each model to be either electric or fuel we need to know operational cost; electric/fuel detailed about smell, smoke, end waste and emmission etc
the supply and installation of an incinerator furnace with a capacity of 300 kg of animal carcasses in a normal working day 5:00 , with burner and all the necessary accessories for its proper functioning . This kiln incinerator must be stationary on a concrete foundation . It will also be provided : the supply and electrical connection between the incinerator furnace and the control cabinet the supply and installation of the fireplace, the supply and fitting of the burner, the supply and installation of all the refractory masonry, the heating tools ( shovels, picks, scrapers , etc. ….. ) . the fuel tank with a capacity of 3000 liters , the daily capacity of 300 liters tank the supply of 3300 liters of diesel , after testing, the connection between the main fuel tank , daily tank and furnace , training of operating and maintenance personnel , commissioning and comprehensive testing of all equipment , the supply water in the incinerator vessel by pipe diameter 26 /34.